Maybe there is no elec­tricity in the socket

• Discon­nect the robotic cleaner power supply from the socket for 30 seconds, then plug the robotic cleaner back in and switch it back on. If it still doesn't work, try another socket. 

Maybe the robotic cleaner's floating cable is not prop­erly connected 

• Recon­nect the robotic cleaner cable to the power supply.

Some­thing could be obstructing the free move­ment of the drive belts, drive tracks or wheels 

• Flip the robotic cleaner upside down and try to rotate the wheels by hand, remove any debris from the drive system (hair, leaves, etc.).

The impeller could be seized by an accu­mu­la­tion of hair

• Discon­nect the robotic cleaner from the power supply. Remove the upper screws from the top of the robotic cleaner and check that the impeller does not need to be cleaned. (DO NOT use elec­tric screw­drivers for this oper­a­tion, use hand tools only).

The motor or the pump is faulty

• Turn the robotic cleaner upside down and try to switch it back on - check that the pump and the motor start.

The power supply or the robotic cleaner still do not work

• Return the robotic cleaner to your agency or contact your online seller's customer service. 

The robotic cleaner moves but does not pump water - the impeller is broken or seized by an accu­mu­la­tion of hair:

• Discon­nect the robotic cleaner power supply before performing this inter­ven­tion.
• Remove the screws from the top of the robotic cleaner and check that the impeller is not broken or in need of cleaning.
• When replacing the robotic cleaner cover, use hand tools only. DO NOT USE power tools for this oper­a­tion. 
• If following this inter­ven­tion, the robotic cleaner is still not working prop­erly, return it to your agency or contact your online seller's customer service. 

The robotic cleaner moves but does not pump water - the filters are very dirty

• Remove the filter and start it without the filter. If it works well, clean the filter thor­oughly or replace it. 

The robotic cleaner starts correctly and then stops after a short time - the filters are very dirty

• Remove the filter and start it without the filter. If it works well, clean the filter thor­oughly or replace it.
• Some­times, the filter can be clogged altough if looks clean. To clean it, soak it in soapy water for 30 minutes and then gently rub the inner surface.

The robotic cleaner travels on 2 wheels at the start of or during the cleaning cycle - the pool surface is too smooth

• Remove the float in the robotic cleaner.
• Check that the pH of the pool water is between 7.0 and 7.4 and correct it if neces­sary.

The robotic cleaner travels on 2 wheels at the start of or during the cleaning cycle - the pool surface is too rough

• Return your robotic cleaner to your agency or contact your online seller's customer service and ask for PVC wheels.

The robotic cleaner does not move but does pump water - debris is preventing rota­tion of the wheels/ belts 

• Turn the wheels by hand.
• Clean them and remove any debris.

The robotic cleaner does not move but does pump water - the internal drive tracks or drive belts are worn

• Check the teeth of the master and slave drive belts.
• Return the robotic cleaner if the teeth are worn.

The robotic cleaner is not designed to mount the pool walls

• Check that your robotic cleaner is not a floor cleaning only model: if you see the refer­ence REFL on the product label, your robotic cleaner is not designed to mount the pools walls. 

The filters are dirty

• Remove the filter and start the robotic cleaner in the pool without it. If it works well, clean the filter. Some­times, the filter may be clogged even though it looks clean.

The impeller is broken or seized by an accu­mu­la­tion of hair

• Discon­nect the robotic cleaner power supply before performing this inter­ven­tion.
• Remove the screws above the water outlet and wheck that the impeller is not broken or in need of cleaning.
• When replacing the robotic cleaner cover, use hand tools only. DO NOT USE power tools for this inter­ven­tion.

The Chlo­rine level is not correct

• Check the Chlo­rine level. If it is very low, carry out a shock treat­ment.
• Remove the robotic cleaner from the pool while adjusting the Chlo­rine level.

The pH level is not correct

• Check that the pH level is between 7.0 and 7.4, correct it if neces­sary.
• Remove the robotic cleaner from the pool while adjusting the pH level.

The water temper­a­ture is not optimal

• Check the water temper­a­ture: if it is less than 13° C, adjust the floats depending on the robotic cleaner model.

The batteries are empty

• Check the batteries by pressing the buttons, the red indi­cator light on the remote control will not light up if the batteries are empty.
• Replace the remote control batteries.

The remote control is not paired with the power supply

• Pair the remote control with the robotic cleaner power supply.
• Refer to the instruc­tions enclosed with the remote control.

Dirty filters can affect move­ment of the robotic cleaner

• Make sure that all the filters are clean.

The filter access hatch under­neath the robotic cleaner is not closed prop­erly

• Make sure that the hatch is closed prop­erly.

The cable was tangled before the robotic cleaner was placed in the pool

• Make sure that the cable is spread out and untan­gled before placing the robotic pool cleaner in the pool.

There is too much cable in the pool

• Make sure that the cable is long enough to reach the end of the pool, but no longer than this. 
• For example, in a 10 m x 5 m pool with the power supply in the middle, do not put more than 6 m of cable in the pool.

The impeller is broken or seized by an accu­mu­la­tion of hair

• Discon­nect the robotic cleaner power supply before carrying out this inter­ven­tion.
• Remove the screws on top of the robotic cleaner and check that the impeller is not broken or in need of cleaning.
• When replacing the robotic cleaner cover, use hand tools only. DO NOT USE power tools for this inter­ven­tion.

The Chlo­rine level is not correct

• Check the Chlo­rine level, make sure that it is not too high. 
• If the PVA brush is completely dissolved/ destroyed - contact your agency or online seller's customer service to replace it.

The pH level is not correct

• Check that the pH is between 7.0 and 7.4, adjust it if neces­sary.
• If the PVA brush is completely dissolved/ destroyed - contact your agency or online seller's customer service to replace it.

The robotic cleaner remained in the water while a water treat­ment was performed 

• Make sure to take the robotic cleaner out of the pool before treating the water.
• If the PVA brush is completely dissolved/ destroyed - contact your agency or online seller's customer service to replace it.

The pool surface finish is very rough (cement/granite/pebbles)

• Contact your agency or online seller's customer service to replace the PVA brushes with PVC brushes.

The impeller is seized by an accu­mu­la­tion of hair or debris

• Discon­nect the robotic cleaner power supply before performing this inter­ven­tion. 
• Remove the screws from the top of the robotic cleaner and check if the impeller needs to be cleaned.
• When replacing the robotic cleaner cover, use hand tools only. DO NOT USE power tools for this inter­ven­tion.

An object is preventing rota­tion of the brushes/ belts

• Turn the brushes/ wheels by hand.
• Remove any debris.

The filter fibres are not perfectly clean, or there are holes in the filter

• Clean if neces­sary and check that there are no holes in the filter.

The impeller is broken or seized by an accu­mu­la­tion of hair or debris

• Discon­nect the robotic cleaner's power supply before performing this inter­ven­tion.
• Remove the screws from the top of the robotic cleaner and check that the impeller is not broken or in need of cleaning. 
• When replacing the robotic cleaner's cover, use hand tools only. DO NOT USE power tools for this inter­ven­tion. 

The intake valves are missing or move­ment is restricted by objects are caught in them

• Check the intake valves under­neath the robotic pool cleaner.
• The intake valves must be able to move freely to open and close.
• Clean and free the intake valve if neces­sary.

The check valves are missing or blocked

• Make sure that the check valves are present on the robotic pool cleaner.
• The check valves must be whole and must cover the entire aper­ture. 

The hatch under the robotic cleaner is not closed correctly

• Make sure that the hatch is closed correctly.

There are holes in the filter

• Check that there are no holes in the filters and that the filter frame is not damaged.

The intake valve are blocked by or missing 

• Check the valves under­neath the robotic cleaner.
• The intake valves should move freely to open and close.
• Clean and free the intake valves if neces­sary.

The cable is not long enough to reach the far end of the pool, or the cable is too tangled 

• Make sure that the cable is long enough to reach the end of the pool but not any longer than that.
• Check that the cable is not tangled.

The orien­ta­tion of the robotic cleaner's handle may affect its travel under water

• Increase the diag­onal angle of the handle by pressing on the handle pin and turning it.

The pH level is not correct

• Check that the pH is between 7.0 and 7.4 in pools treated with Chlo­rine, or between 7.0 and 8.0 in pools treated with Bromine.
• Remove the robotic cleaner from the pool while adjusting the pH.

The Chlo­rine level is not correct

• Check the Chlo­rine level, if it is very low, carry out a shock treat­ment.
• Remove the robotic cleaner from the pool while adjusting the Chlo­rine level. 

The impeller is broken or seized by the accu­mu­la­tion of hair 

• Discon­nect the robotic cleaner power supply before this inter­ven­tion.
• Remove the upper screws from the top of the robot and check that the impeller is not broken or seized and in need of cleaning.
• When replacing the cover on the robotic cleaner, use hand tools only. DO NOT USE power tools for this oper­a­tion.

There is an obstacle stuck in the belt or gear system

• Try to rotate the brushes/ wheels by hand.
• Clean the drive system, remove any debris.